Olympia Chimney Flue Liner Replacement Nationwide

Olympia Chimney Flue Liner Replacement: The Bristol Owner’s Guide

If you have an Olympia Chimney liner that’s cracked, rusted through, or letting flue gases seep into the house, replacement in Bristol typically runs $1,800 to $3,400 installed for a standard single-story run, and we keep the common sizes on the truck. Most owners find out the hard way: a puff of smoke in the living room, water streaks on the firebox wall, or a sweep’s camera showing a gap where metal should be. The good news is this is a job we do regularly around Bristol, and it’s almost always done in half a day once the liner is on site.

Call (860) 743-7743

Which Olympia Chimney Models This Applies To

We match replacement liners to whatever Olympia Chimney appliance or venting system you’ve got, whether it’s a stainless rigid liner from their round-series lineup, a flexible 316Ti liner, or a furnace connector pipe. The easiest way to identify what you need is the ID tag on the appliance, but most chimneys don’t give you one, so we measure the flue diameter directly and check the existing liner wall against the appliance BTU rating. A gas furnace needs a smaller cross-section than an oil burner, and that matters: too big and the flue never warms up, so it condenses and rots from the inside.

One thing to know about Olympia Chimney parts specifically: their liners are cut to length on site, so there’s no “model number” on the pipe itself half the time. What matters is gauge, diameter, and whether you need 316Ti stainless for oil or gas. We carry DuraFlex and HeatShield liners as quality equivalents when the Olympia parts are backordered, and we’ll tell you which one we’d put in our own house.

Signs Your Olympia Chimney Flue Liner Replacement Is Failing

• Flue gases backing into the house. You smell smoke or exhaust when the system runs. That means the liner has a breach or is plugged, and the gasses are finding the path of least resistance. This is the one that gets our attention fastest.
• Water running down the firebox or furnace flue. A pinhole lets condensation and rain wick in, and the water does not evaporate quickly in a Bristol winter. You’ll see rust-colored streaks or a damp smell in the room.
• Flakes and debris accumulating in the cleanout. When the liner flake metal starts dropping, the liner has been hot beyond its rating, usually because the wrong fuel was burned or the liner was already old enough to vote.
• Visible rust, gaps, or cracks in an exposed section. You can inspect the connector pipe yourself with a flashlight. If the metal looks scaled or the seams are opening, the section needs replacing.
• The appliance burner keeps short-cycling or the flue damper won’t hold a setting. A backed-up flue changes the draft, which changes the burn. It’s the less obvious sign, but it shows up on a lot of Bristol service calls before anyone opens the chimney.

Replacement Cost & What’s Included

For Bristol homes, a straight Olympia Chimney flue liner replacement usually lands between $1,800 and $3,400 installed. That includes removing the old liner, installing the new one with the correct top plate and rain cap, connecting it to the appliance, and doing a draft test before we call it done. The range comes down to how tall your run is, whether it’s single-story or two, and whether we’re pulling a liner through an existing chimney or doing a direct vent replacement.

You’ll get the number in writing before a tool comes off the truck, and we stand behind the work with our 90-Day Done Right Promise: if it’s not right, one call brings Wendell and his crew back at no charge. If the liner is damaged but the job does not need doing yet, Wendell will tell you that instead. We will not sell a replacement on a scare.

DIY or Call Us?

You can check the connector pipe where it enters the wall or appliance, and you can watch for rust flakes or moisture in the cleanout. That’s your job. Pulling a liner out of a chimney and properly re-venting an oil or gas appliance is not a Saturday project: the liner has to be sized to the appliance, sealed at both ends, supported correctly, and the old flue gas path must be isolated. Get it wrong and you can end up with carbon monoxide migrating through a wall cavity, and that does not announce itself. Call (860) 743-7743 and we’ll get a camera up the flue and give you the honest verdict.

FAQs