Olympia Chimney Chimney Cap & Crown Nationwide

Olympia Chimney Chimney Cap & Crown in Bristol: What to Know First

Chimney cap and crown work on Olympia Chimney systems in Bristol typically runs between $185 and $950 depending on whether we’re sealing a hairline crack or replacing a rusted multi-flue cap. Most jobs are finished the same day we start, and you’ll know the exact price before any tool comes off the truck. If you own a home in Bristol with an Olympia flue and you’re seeing water stains near the fireplace or hearing drips inside the chimney, give us a call at (860) 743-7743 and we’ll walk you through what you’re likely dealing with.

Call (860) 743-7743

This page is for Bristol homeowners with Olympia Chimney products who need honest answers about caps, crowns, and whether the leak is actually coming from either one. Not every wet chimney is a cap problem. Some are crown failures. Some are both. We’ll tell you which, and we’ll show you the camera footage to prove it.

How Olympia Chimney Products Fail - and How We Fix Them

Olympia Chimney makes solid equipment, but we’ve been inside enough Bristol flues to know exactly where their systems break down. Here’s what we see most:

• Olympia stainless caps rust at the mesh seam. The stainless bodies hold up fine, but the screen welds on older Olympia Vacu-Stack and standard caps are the first place moisture gets in. Once the mesh separates from the band, birds follow. We replace with a heavier-gauge aftermarket cap or a factory-match depending on what the flue needs.
• Crown cracks on masonry chimneys with Olympia liners. The liner itself isn’t the problem. It’s the concrete crown poured over it. Bristol freeze-thaw cycles live here, and a crown without an expansion joint will crack within five to seven years. Water gets under the chase cover, works down the outside of the Olympia liner, and eventually rots the framing around the chase or eats the brick below.
• Olympia chase covers with flat tops pond water. Flat or low-slope chase covers trapped into Olympia installation specs collect standing water, especially on older raised-ranch homes near Lake Compounce where the chimneys sit partially exposed to prevailing wind. We refabricate or add cross-break slope so water sheds instead of sitting. Simple fix, big difference.
• Multi-flue Olympia caps without dividers. Two flues sharing one cap, one active fireplace, one dormant. The dormant flue scavenges exhaust back down into the house. We install Olympus multi-flue caps with proper dividers so each flue terminates independently, and we check both flues while we’re up there.
• OEM cap fasteners loosening on Olympia prefab units. The set screws and brackets Olympia specifies work fine at install. Ten years of Bristol temperature swings later, the cap has shifted off-center. An off-center cap lets rain angle straight down the flue tile. We correct it, add if needed, and verify the cap sits centered before we come down off the roof.

Our Olympia Chimney Chimney Cap & Crown Process

When you call about Olympia Chimney cap or crown work in Bristol, here’s how it goes:

1. 1
   You call (860) 743-7743. A live person answers. We ask what you’re seeing, when it started, and what kind of system you have. We give you a ballpark over the phone, straight up.
2. 2
   We show up on time, in uniform, and actually introduce ourselves. Wendell and the crew drive Bristol roads daily. You’ll get a real arrival window, not a four-hour spread.
3. 3
   The camera goes up the flue before anything gets touched. We look at the cap, the crown, the chase cover, and the liner. You watch the footage with us.
4. 4
   We decide OEM or quality aftermarket together. If the Olympia part still works, we repair it. If it doesn’t, we quote both options and tell you which one we’d put on our own house. No pressure either way.
5. 5
   The work is done same day in most cases. Crown coating, cap replacement, custom fabrication, multi-flue setup. We clean up the roof, the yard, and the firebox before we leave.
6. 6
   The 90-Day Done Right Promise goes in writing. If it’s not right, you call, and we come back. No arguing, no invoice.

What Olympia Chimney Chimney Cap & Crown Costs in Bristol

Here’s straight pricing for the Olympia Chimney cap and crown jobs we do around Bristol:

• Standard single-flue cap replacement: $185 to $340
• Custom stainless cap for oversized or oval Olympia flues: $350 to $650
• Multi-flue cap with dividers: $420 to $950 depending on width and access
• Crown sealing (hairline cracks, no rebuild): $275 to $500
• Crown rebuild with expansion joint: $600 to $1,150

What moves the price: roof pitch, chimney height, whether we need staging, and whether the crown needs rebuilding versus sealing. You’ll get an exact number before we start. No trip charge inside the county, and remember the standing offers: $40 off any repair over $200, and 10% off always for seniors and veterans.

Why Bristol Homeowners Call Top Hat Chimney for Olympia Chimney Work

We’ve been at this since 1999, and we’re not a franchise that rotated in last spring. Wendell Pike put his name on this company and he runs into you on Saturday at the hardware store. That changes how the work gets done. We’re an independent Olympia Chimney service provider, not a factory-authorized shop, so we recommend what the flue needs rather than what the warranty paperwork says. If an aftermarket cap outlasts the OEM part for less money, that’s what we tell you. We also work daily with DuraFlex, HeatShield, and Gelco, so if the discovery on your Olympia system turns into a liner question, you’re already talking to someone who knows the answer. The 90-Day Done Right Promise is in writing on every job. One call brings us back. No fine print about what counts as “done.”

And here’s the plain version: if it needs doing, we will do it right. If it does not, I will tell you that instead.

FAQs